Видео

Thank you!

Thanks so much, man, priceless video

Thank you.

Thanks for showing us where you struggled. I did the same but you were more detailed than the other videos which made it easier. Thank you for the effort. Chuck from Northern California.

Thanks for this video man

Change both crush washers 🎉

Que aceite utilizaste?

I have a cuestion, this thing change the sound of the motor a little?

I have got a similiar setup. Quick question: Does everything go as a single track in your DAW or as a separate tracks for each mic?

I'm about to replace the door handles in a 99 Prelude, and this was helpful. I think the design is close enough to the Civic door and handles that this video applies to both. I didn't fully "trust" the procedure in the Prelude service manual because the instructions have you start with unscrewing the latch that is on the end of the door! It's describing how to strip off all of the parts, and doesn't explain whether I could remove the handle without taking apart all those other things. Interestingly the service manual does say pull the handle out before removing the second rod, but it doesn't explain why. Your video explains why; it's for access and get a better angle at it than you can get from the back side.

How many quarts do you put back in?

Pushing the lock into the sager was a great move thanks, you solved me a big problem🎉

1st and foremost your using steel drums and should be using Brass! Throw a fiberskyn on to get rid of the Highs and overtones… Of course technique is a factor as well! Don’t just go full on from the thigh on the pedal, practice a little heel down and feather the pedal to dampen the rebound and squeak. 😮

can brake cleaner touch the surface of the Shoe?

I have to do the same thing to my 2011 silverado, every 2 oil changes i have to clean and lubricate the contact points with high temp purple grease for brakes.Its annoying as hell.

my 2017 silverado makes a squeak when realismg the brake tought it was the suspension but put my face infront of my rear wheel drivers side and hot the breaks and it comes from the caliper i

My clip keeps falling out now huh such a poor design.

Good job. Solve my problem

I appreciate you bud! That stupid clip behind the metal should for pick cylinder is easy I was missing.

Aside from brake dust and/or road dirt, has anyone found a different cause for this symptom? I'm trying to figure out if letting it slide can be something more dangerous. I'm hoping that this really simple and cheap solution works for me; Thanks for sharing!

This video helped alot Thank you bro!

Thanks for the vid bro. Very helpful. The small tips with your trial and error are great.

I changed pads 2 months ago all 4 wheels, i hear some squeaking recently after i release the breake pedal, but only when im moving, no other noises when im stopped and pressing , releasing then pedal, anyone have an idea what it can be?

Thank you for sharing this. Even though this is a niche problem I’m glad this was covered

best explanation of this process. cheers bud

Ty

I think I hear my in front wheel ?

Thank you!! That damn hidden clip was kicking my a$$ !!

Good video. Liked the easy mello tone of it, as well as the lack of music. I was only going to change the lock cylinder and this video will save me alot of money, since after watching this I'm willing to tackle the job. How much money? Honda Dealer (NJ) wants 400$. Local locksmith wants 320$. the lock price was also obscene. a keyed cylinder was around 200$

Brother great video literally did everything you said on my 2008 Honda fit worked wonderfully set there for 10 minutes going dam where my 8 mm bolts so had to go to the hardware store get some but thanks so much

Mine has the handle to put the window down wondering how do i remove the panel with out breaking it?

What kind of oil do you use?

I watch a lot of informational videos on how to disassemble things in the car because I am a locksmith without a doubt this is the best video I have seen to date. A light and simple and pleasant explanation and professional photography.

Very very thank

Cheapest way to fix this?

Great video, I really like how you point the camera right at the handle from the inside and tell us what we need to do. Someone busted my locks in and this will be a huge help replacing them.

I don't know if it was said before but @9:44 twist the entire handle assemble and unscrew it from the rod instead of trying to unclip it. My replacement handle from the junk yard had the clip on it.

This video is low key extremely well done...just shows you dont need alot of camera equipment to make a good video just a smart guy with a camera!!! I think it was perfect bro thanks a ton!!!

Hey man first off I know this is a bit old but its a great video and its much appreciated! I wanted to ask you, did you have your handle repainted or did you just put it on the way it came out the box? And if you did not paint it, did the shine on the black plastic hold up or did it fade to a foggy grey and oxidize over this past year or so?

As soon as you made the sound I knew I was at the right video

Clear and easy to understand, thanks.

Thank you! Awesome of you to be quick but precise. I appreciate the help :)

Thanks bro.

Do you take off the fill plug first and then the drain plug? Other ppl in comments on this are saying don’t do the drain plug first and then the fill plug. Well yeah lol

i would do this but i don’t have any materials for this. or tools!

My basements windows busted out during this in Southern, IL

Thank you dude! This just started on my 2002 Tundra. Gonna tackle it this afternoon.

I just need to replace the lock cylinder so just take the clip off and that’s it??

Don't use brake cleaner on the cylinder seals!! Be careful there. ;)

8 years ago damn.. what were the songs used?